911 to Stain Removal for Your Natural Stone

Your granite is sealed, your marble is polished, you wipe up spills immediately, and suddenly you come home one day and the kids have strawberry sips drizzling over your counter tops. What do you do? Try as you might there is red residue on your golden counters.

I found this article that was just published through the Marble Institute of America and thought I would pass it on to you.

 

Stains

Spills and Stains

Blot the spill with a paper towel immediately. Don’t wipe the area, it will spread the spill. Flush the area with plain water and mild soap and rinse several times. Dry the area thoroughly with a soft cloth. Repeat as necessary. If the stain remains, refer to the section in this brochure on stain removal.

Stain Removal

Identifying the type of stain on the stone surface is the key to removing it. If you don’t know what caused the stain, play detective. Where is the stain located? Is it near a plant, a food service area, an area where cosmetics are used? What color is it? What is the shape or pattern? What goes on in the area around the stain? Surface stains can often be removed by cleaning with an appropriate cleaning product or household chemical. Deep-seated or stubborn stains may require using a poultice or calling in a professional. The following sections describe the types of stains that you may have to deal with and appropriate household chemicals to use and how to prepare and apply a poultice to remove the stain.

Types of Stains and First Step Cleaning Actions

OIL-BASED (grease, tar, cooking oil, milk, cosmetics)

An oil-based stain will darken the stone and normally must be chemically dissolved so the source of the stain can be flushed or rinsed away. Clean gently with a soft, liquid cleanser with bleach OR household detergent OR ammonia OR mineral spirits OR acetone.

ORGANIC (coffee, tea, fruit, tobacco, paper, food, urine, leaves, bark, bird droppings)

May cause a pinkish-brown stain and may disappear after the source of the stain has been removed. Outdoors, with the sources removed, normal sun and rain action will generally bleach out the stains. Indoors, clean with12% hydrogen peroxide (hair bleaching strength) and a few drops of ammonia.

METAL (iron, rust, copper, bronze)

Iron or rust stains are orange to brown in color and follow the shape of the staining object such as nails, bolts, screws, cans, flower pots, metal furniture. Copper and bronze stains appear as green or muddy-brown and result from the action of moisture on nearby or embedded bronze, copper or brass items. Metal stains must be removed with a poultice.(See section on Making & Using a Poultice) Deep-seated, rusty stains are extremely difficult to remove and the stone may be permanently stained.

EFFLORESCENCE

Efflorescence is a white powder that may appear on the surface of the stone. It is caused by water carrying mineral salts from below the surface of the stone rising through the stone and evaporating. When the water evaporates, it leaves the powdery substance. If the installation is new, dust mop or vacuum the powder. You may have to do this several times as the stone dries out. Do not use water to remove the powder; it will only temporarily disappear. If the problem persists, contact your installer to help identify and remove the cause of the moisture.

Poultices

Making and Using a Poultice

A poultice is a liquid cleaner or chemical mixed with a white absorbent material to form a paste about the consistency of peanut butter. The poultice is spread over the stained area to a thickness of about 1/4 to 1/2 inch with a wood or plastic spatula, covered with plastic and left to work for 24 to 48 hours. The liquid cleaner or chemical will draw out the stain into the absorbent material. Poultice procedures may have to be repeated to thoroughly remove a stain, but some stains may never be completely removed.

Poultice Materials
Poultice materials include kaolin, fuller’s earth, whiting, diatomaceous earth, powdered chalk, white molding plaster or talc. Approximately one pound of prepared poultice material will cover one square foot. Do not use whiting or iron-type clays such as fuller’s earth with acid chemicals. The reaction will cancel the effect of the poultice. A poultice can also be prepared using white cotton balls, whitepaper towels or gauze pads.

Cleaning Agents or Chemicals

OIL-BASED STAINS

Poultice with baking soda and water OR one of the powdered poultice materials and mineral spirits.

ORGANIC STAINS

Poultice with one of the powdered poultice materials and 12% hydrogen peroxide solution (hair bleaching strength) OR use acetone instead of the hydrogen peroxide.

IRON STAINS

Poultice with diatomaceous earth and a commercially available rust remover. Rust stains are particularly difficult to remove. You may need to call a professional.

COPPER STAINS

Poultice with one of the powdered poultice materials and ammonia. These stains are difficult to remove. You may need to call a professional.

BIOLOGICAL STAINS

Poultice with diluted ammonia OR bleach OR hydrogen peroxide. DO NOT MIX AMMONIA AND BLEACH! THIS  COMBINATION CREATES A TOXIC AND LETHAL GAS!

Applying the Poultice

Prepare the poultice. If using powder, mix the cleaning agent or chemical to a thick paste the consistency of peanut butter. If using paper, soak in the chemical and let drain. Don’t let the liquid drip.

Wet the stained area with distilled water.

Apply the poultice to the stained area about 1/4 to 1/2 inch thick and extend the poultice beyond the stained area by about one inch. Use a wood or plastic scraper to spread the poultice evenly.

Cover the poultice with plastic and tape the edges to seal it.

Allow the poultice to dry thoroughly, usually about 24 to 48 hours. The drying process is what pulls the stain out of the stone and into the poultice material. After about 24 hours, remove the plastic and allow the poultice to dry.

Remove the poultice from the stain. Rinse with distilled water and buff dry with a soft cloth. Use the wood or plastic scraper if necessary.

Repeat the poultice application if the stain is not removed. It may take up to five applications for difficult stains.

If the surface is etched by the chemical, apply polishing powder and buff with burlap or felt buffing pad to restore the surface.

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>